*Drive*- Здесь рулят padonki

После обновления Ubuntu 8.04 LTS SERVER до 10.04 пропал доступ на сетевые шары samba.

NETSTAT показал, что samba после обновления перестала слушать ipv4. А висела на ipv6 порт 139.

Это решил просто - отрубил поддержку ipv6 : после надо ребутнуть сервак.

А вот с недомтупностью шар - пришлось поломать голову: Вапрос решился до банального просто : в настройке samba добавил:

ну раз это интересует то вот ваще то :
http://daemon.drivesource.ru

Padonak писал(а):

Код: Выделить всё

bind interfaces only = yes
interfaces = eth1 127.0.0.1/8 192.168.0.0/24
socket address = 192.168.0.1

При раскоментировании строки interfaces = eth1 127.0.0.1/8 192.168.0.0/24 (у меня eth0), то пропадают все компы из сети)).

Kodla писал(а):

Padonak писал(а):

Код: Выделить всё

bind interfaces only = yes
interfaces = eth1 127.0.0.1/8 192.168.0.0/24
socket address = 192.168.0.1

При раскоментировании строки interfaces = eth1 127.0.0.1/8 192.168.0.0/24 (у меня eth0), то пропадают все компы из сети)).

1. У тебя точно интрефейс eth1 ?
2. У тебя точно сеть 192.168.0.0/24 ?

З.Ы. надо по своим параметрам это делать

august@EUGENE:~$ sudo ifconfig
enp3s0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:24:54:38:09:bd txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 970 bytes 76993 (75.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 970 bytes 76993 (75.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

wlp2s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.71 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 2a00813a:241:7659a53d:dfeb prefixlen 64 scopeid 0x0<global>
inet6 fe80::b934:f3fc9a12 prefixlen 64 scopeid 0x20<link>
inet6 2a00813a:241:ca8e:90824c44 prefixlen 128 scopeid 0x0<global>
ether 00:26:b6:5f:d5:d8 txqueuelen 1000 (Ethernet)
RX packets 271708 bytes 268443242 (256.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 165063 bytes 43882238 (41.8 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
# - When such options are commented with ";", the proposed setting
# differs from the default Samba behaviour
# - When commented with "#", the proposed setting is the default
# behaviour of Samba but the option is considered important
# enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.

#======================= Global Settings =======================

[global]

## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of
workgroup = AUGUST
# server min protocol = SMB2
client max protocol = NT1


#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
; interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself. However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
; bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
log file = /var/log/samba/log.%m

# Cap the size of the individual log files (in KiB).
max log size = 1000

# We want Samba to only log to /var/log/samba/log.{smbd,nmbd}.
# Append syslog@1 if you want important messages to be sent to syslog too.
logging = file

# Do something sensible when Samba crashes: mail the admin a backtrace
panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# Server role. Defines in which mode Samba will operate. Possible
# values are "standalone server", "member server", "classic primary
# domain controller", "classic backup domain controller", "active
# directory domain controller".
#
# Most people will want "standalone server" or "member server".
# Running as "active directory domain controller" will require first
# running "samba-tool domain provision" to wipe databases and create a
# new domain.
server role = standalone server

obey pam restrictions = yes

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
unix password sync = yes

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
passwd program = /usr/bin/passwd %u
passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
pam password change = yes

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
map to guest = bad user

########## Domains ###########

#
# The following settings only takes effect if 'server role = primary
# classic domain controller', 'server role = backup domain controller'
# or 'domain logons' is set
#

# It specifies the location of the user's
# profile directory from the client point of view) The following
# required a [profiles] share to be setup on the samba server (see
# below)
; logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
# logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
; logon drive = H:
# logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
; logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe. The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the
# SAMR RPC pipe.
# The following assumes a "machines" group exists on the system
; add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe.
; add group script = /usr/sbin/addgroup --force-badname %g

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
; include = /home/samba/etc/smb.conf.%m

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
; idmap config * : backend = tdb
; idmap config * : range = 3000-7999
; idmap config YOURDOMAINHERE : backend = tdb
; idmap config YOURDOMAINHERE : range = 100000-999999
; template shell = /bin/bash

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 means that usershare is disabled.
# usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
usershare allow guests = yes

#======================= Share Definitions =======================

[homes]
comment = Home Directories
browseable = no

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
read only = yes

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server.
# The following parameter makes sure that only "username" can connect
# to \\server\username
# This might need tweaking when using external authentication schemes
valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
; comment = Network Logon Service
; path = /home/samba/netlogon
; guest ok = yes
; read only = yes

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
; comment = Users profiles
; path = /home/samba/profiles
; guest ok = no
; browseable = no
; create mask = 0600
; directory mask = 0700

[printers]
comment = All Printers
browseable = no
path = /var/spool/samba
printable = yes
guest ok = no
read only = yes
create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
comment = Printer Drivers
path = /var/lib/samba/printers
browseable = yes
read only = yes
guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
; write list = root, @lpadmin

тебе эта настройка нахрен не нужна Это настройка на сервере, особенно на шлюзе, чтоб SAMBA наружу не выходила, на всякий случай, если что то с файерволом случицца. Забей !

Padonak писал(а):тебе эта настройка нахрен не нужна Это настройка на сервере, особенно на шлюзе, чтоб SAMBA наружу не выходила, на всякий случай, если что то с файерволом случицца. Забей !

А компы на винде как увидеть? Кстати, обновил один ноут с 7ки до 10ки домашней, и ноут перестал видеть сеть.

SMBv1 не устанавливается по умолчанию в Windows 10 версии 1709, Windows Server версии 1709 и более поздних версиях.
Как включить >>

Padonak писал(а):SMBv1 не устанавливается по умолчанию в Windows 10 версии 1709, Windows Server версии 1709 и более поздних версиях.
Как включить >>

Спасибо, помогло. Вот же ж... А я уж хотел все машины опингвинить))).

И еще. Как оказалось, роутер от МГТС поддерживает только протокол SMB1. Сын с онлайма на мгтс перешел, скорость у них побольше по оптоволокну. На роутере ASUS был SMB2, и все работало.